Corrosion-Resistant Titanium Solutions for Seawater Desalination

Maximize thermal efficiency, prevent localized pitting in high-saline environments, and extend plant operational lifespans with premium marine-grade titanium tubing and components.

SCROLL

Engineered for Harsh Desalination Environments

Advanced titanium manufacturing engineered to eliminate crevice corrosion, erosion-corrosion, and biofouling in thermal and membrane desalination systems.

MSF & MED Thermal Evaporators

Commercially pure titanium (Grade 1 & Grade 2) thin-wall tubes designed for maximum heat transfer coefficient and total resistance to boiling seawater corrosion.

Reverse Osmosis (SWRO) Piping

High-pressure titanium piping manifolds and Grade 9 (Ti-3Al-2.5V) tubing engineered to withstand extreme hydraulic pressures (up to 80+ bar) without cracking.

Intake & Brine Discharge Systems

Palladium-enhanced titanium alloys (Grade 7 & Grade 12) developed for severe crevice corrosion resistance in high-temperature brine concentrates.

Pumps, Valves & Fasteners

Forged Grade 5 (Ti-6Al-4V) valve bodies, pump impellers, and corrosion-proof bolts engineered for long-term reliability in high-velocity seawater pumps.

Marine-Grade Mill Products & Desalination Components

Fully compliant with ASTM B338, ASTM B861/B862, ASTM B265, and ISO 9001 quality guidelines.

Seamless Titanium Heat Exchanger Tubes Grade 2
ASTM B338 / ASME SB338

Grade 2 Titanium Heat Exchanger Tubes

Thin-wall seamless and welded titanium tubes engineered for MSF/MED heat recovery rejection sections and condenser bundles.

  • Outer Diameter: 12.7mm to 50.8mm
  • Wall Thickness: 0.5mm to 1.65mm
  • 100% Eddy Current & Pneumatic Pressure Tested
Get Product Spec Sheet
ASTM B265 Grade 7 Titanium Sheets and Plates
ASTM B265 / Grade 7 (Ti-Pd)

Grade 7 Titanium Plates & Tube Sheets

Palladium-alloyed titanium plates optimized for SWRO high-pressure vessel end caps, tube sheets, and plate heat exchangers.

  • Thickness: 1.0mm to 80mm
  • Superior Resistance to Crevice Corrosion in Hot Brine
  • Full Material Traceability & EN 10204 3.1 Certified
Inquire Plate Specs
Large Diameter Titanium Welded Pipe Grade 2
ASTM B862 / ASME SB862

Large Diameter Welded Titanium Pipes

Heavy-wall welded titanium piping systems engineered for intake manifolds, high-salinity discharge lines, and chemical feed loops.

  • Nominal Size: 2" to 48" (DN50 - DN1200)
  • Zero Corrosion Rate in Untreated Seawater
  • X-Ray Radiographic & Hydrostatic Tested
Request Pipe Catalog
High-Pressure Titanium Flanges and Forgings
ASTM B381 / ASME B16.5

Titanium Forged Flanges & Fittings

Precision forged Grade 2 & Grade 5 blind, weld-neck, and slip-on flanges built for high-pressure reverse osmosis piping connections.

  • Pressure Ratings: Class 150 to Class 2500
  • Prevents Galvanic Corrosion in Marine Systems
  • 100% Ultrasonic & Liquid Penetrant Tested
Request Flange Data Sheet

Field-Tested Desalination Performance

Discover how Kintonti Metal delivers long-term corrosion resistance and maintenance savings for commercial desalination projects worldwide.

SWRO Desalination Plant

High-Pressure RO Manifold Corrosion Replacement

Location: Middle East Coastal Desalination Facility

Challenge: Severe pitting and crevice corrosion on 316L and duplex stainless steel high-pressure manifolds after 18 months of operation.

Solution: Replaced failed manifold headers with custom-fabricated ASTM B862 Grade 2 Titanium Welded Piping and Grade 7 flanges.

25+ Yrs
Maintenance-Free Lifespan
0 mm/yr
Seawater Corrosion Rate
MSF Thermal Desalination

Heat Exchanger Evaporator Bundle Retrofit

Location: Mediterranean Thermal Power & Desalination Plant

Challenge: High tube failure rates due to erosion-corrosion and biofouling in cupronickel (Cu-Ni 70/30) heat exchanger tubes.

Solution: Supplied over 120,000 meters of thin-wall ASTM B338 Grade 2 Titanium Heat Exchanger Tubing for full bundle retubing.

100%
Tube Leak Elimination
18%
Thermal Efficiency Gain

Desalination Titanium Alloy Selection Matrix

Technical reference guide for metallurgical selection across seawater thermal and reverse osmosis systems.

Alloy Grade Composition Spec Key Performance Characteristics Best Used For
Grade 1 Titanium Unalloyed Titanium (Low Oxygen) Maximum formability, excellent cold workability, complete resistance to raw seawater corrosion. Plate heat exchangers (PHE), thin corrugated plates, complex deep-drawn stampings.
Grade 2 Titanium Commercially Pure Titanium Optimal balance of strength, ductility, weldability, and zero general corrosion in marine water. MSF/MED heat exchanger tubes, SWRO low-pressure piping, sea water intake lines.
Grade 7 (Ti-0.15Pd) Unalloyed Titanium + 0.15% Palladium Superior resistance to crevice corrosion in hot, acidic, or highly concentrated brine environments (>100°C). High-temperature brine heaters, evaporator tube sheets, seal face regions.
Grade 12 (Ti-0.3Mo-0.8Ni) Ti-Mo-Ni Low-Alloy Titanium Higher tensile strength than Gr.2 with elevated crevice corrosion resistance at high temperatures. High-pressure brine vessels, evaporators, chemical feed lines in desalination plants.

Desalination Engineering FAQ

Technical insights and metallurgical guidance from our marine materials division.

Why is titanium superior to duplex stainless steel in seawater desalination plants?

While Super Duplex stainless steels (e.g., 2507) offer good resistance, they remain susceptible to pitting and crevice corrosion in stagnant seawater or at temperatures above 60°C. Commercially Pure Titanium (Grade 2) and Grade 7 form a permanent, self-healing oxide layer ($TiO_2$) that renders them 100% immune to pitting and crevice corrosion in seawater at all ambient temperatures and salinities.

What ASTM/ASME specifications and material test certificates do you provide?

Kintonti Metal complies fully with ISO 9001 and marine industry standards. All desalination tubes, pipes, and plates are supplied with complete Material Test Reports (MTR) according to EN 10204 3.1. Key product specifications include ASTM B338 / ASME SB338 (condenser tubing), ASTM B861 / B862 (seamless & welded pipes), and ASTM B265 (plates).

Is Grade 2 or Grade 7 titanium recommended for thermal desalination evaporators?

For standard heat recovery sections operating below 80°C, Grade 2 Titanium is the industry standard due to its excellent cost-to-performance ratio. For high-temperature brine heaters or tight crevice areas operating above 80°C–90°C with concentrated brine, Grade 7 (Ti-Pd) or Grade 12 (Ti-Mo-Ni) is recommended to eliminate crevice corrosion risk entirely.

How does thin-wall titanium tubing improve thermal efficiency and reduce cost?

Because titanium has complete corrosion resistance in seawater, engineers do not need to add a "corrosion allowance" to wall thickness. Thin-wall titanium tubes (0.5mm to 0.7mm) significantly increase overall heat transfer efficiency while dramatically reducing total material weight and raw material cost per meter.

Ready to Upgrade Your Desalination Piping & Tubing?

Get custom quotes, ASTM/ASME technical specs, and EN 10204 3.1 mill test certificates within 24 hours.